Malco HVACPRO2 Install & Service HVAC Pro Kit, 25-Piece with VETO® TECH PAC | HC1 Hole Cutter, TurboShear®, Full C-RHEX® Driver System | Cutting, Crimping, Fastening & Layout

Descripción

Product description The Right Kit for the Tech Who Does Both Installation and Service Work. Most HVAC techs don't do just installs or just service, they do both, sometimes on the same day. The Malco Install & Service Pro Kit is built around that reality. Twenty-four tools, selected for the work that actually shows up on a typical job: cutting sheet metal, crimping collars, punching holes, fastening, forming, and getting duct runs done. Two power-assisted tools that earn their place every day. The HC1 chucks into your cordless drill and punches clean 2"–12" holes in 20-gauge galvanized, no step bits, no mess. The TS1 converts that same drill into a sheet metal shear for ductwork, panels, and trim cuts. Both tools do in minutes what takes considerably longer by hand, and both run off drills you already own. The complete C-RHEX fastening system, all in one kit. Six C-RHEX drivers and accessories cover every hex fastening application you run into. The KITCRB hard case keeps everything organized and the HPG2 Premium Grip handle gives you a solid manual option when a drill isn't the right tool for the space. Carried in the Veto TECH PAC. The same backpack that working HVAC techs come back to year after year. 46+ vertical pockets, waterproof base, stays upright and organized whether it's open on the van floor or closed on your back going up a ladder. Profesional HVAC Tools from Malco Tools Previous page Next page Veto Pro Pac Tech Pac Malco + Veto HVAC Profesional HVAC Kits

Características

• 24 MALCO TOOLS SELECTED FOR INSTALLATION AND SERVICE WORK: This kit was built around the tools a working HVAC tech actually reaches for on installation and service jobs every day. Cutting, crimping, forming, hole cutting, tie tensioning, duct work, fastening, and layout, it's all covered. Sized for the tech who does real install and service work and wants the right setup.
• HC1 HOLE CUTTER AND TURBOSHEAR INCLUDED: The HC1 Hole Cutter chucks into any cordless drill and cuts clean, accurate 2"–12" holes in 20-gauge galvanized without step bits or knockout punches. The TS1 TurboShear converts your drill into a sheet metal shear for fast straight and curved cuts through ductwork, panels, and sheet metal. On jobs where you're cutting holes and metal all day, these two tools change the pace.
• COMPLETE C-RHEX DRIVER SYSTEM FOR EVERY FASTENING APPLICATION ON ONE JOB: The kit includes the full Malco C-RHEX lineup: the 7-in-1 Phillips Flip Bit, 2" and 6" Building Construction drivers, GOBLUE Variety Pack, 2" Sawtooth driver, the KITCRB hard case install kit, and a Premium Grip handle. Whether you're driving self-piercing screws, or phillips heads, the right driver is in the bag.
• FULL CUTTING, FORMING & DUCTWORK LINEUP FOR DAY-TO-DAY INSTALL AND SERVICE: Max2000 left and right cut snips, Gripped Andy Snips, 5-blade crimper, snap lock punch, 15/16" notcher, 3" hand seamer, 12" folding tool, tie tensioning tool, duct knife, duct stretcher, TinMaster hammer, 16" tape measure, sheet metal scribe, and magnetic torpedo level. The tools that handle every recurring task on an HVAC installation or service call.
• GENUINE VETO TECH PAC BACKPACK: The TECH PAC has 46+ vertical pockets, a patented dual tool bay center panel, and a waterproof injection-molded base that keeps tools dry whether you set it on a rooftop, a van floor, or a mechanical room floor. Tools stand upright so you can see everything at a glance and pull what you need without unpacking the bag. Ergonomic padded straps balance the load for ladder work and long-distance jobsite travel.

Especificaciones