Buscador de vigas Escáner de pared Sensor detector de madera y metales para pared de 3/4 de pulgada de espesor (ST102 (viene con batería))

Descripción

Product description The stud detector quickly locates wood and metal hidden in the walls, floors and ceilings of the house. It can work on different wall surfaces, such as lath, wallpaper wood flooring, acoustic ceiling, painted walls, etc. Helping you find the exact stud while installing TVs, cabinets, garage shelves etc. ST102 stud finders are great for locating the studs behind your walls. Knowing where those are is crucial so you can be sure to screw into them instead of just the drywall when you’re hanging something heavy, like a mirror or a mount for, say, a flat-screen TV. Its small profile is easy enough to store in a drawer or toolbox until you need it. No matter professionals, homeowner and DIY enthusiasts, it must be an ultimate choice Package Included: 1 x Stud Finder1 x 9V Battery1 x User ManualStandard Factory Package Quick locate the stud/metal/pipe/joist/behind the wall/ceiling etc When calibrating, if the stud finder is just in the center of the wood, the product can also be tested directly to the center of the stud 3/4 inches deep detection for wood and metal Stud finder with light indicator & audio alarm Its small profile is easy enough to store in a drawer or toolbox One-step operation, just press the button Application for installing TVs, picture frame, cabinets, garage shelves, etc. Scanning different surfaces: lath, wallpaper wood flooring, acoustic ceiling, painted walls, etc. Stud Scan Detection Metal Scan Detection Pipe Scan Detection How To Use eOUTIL ST102 Stud Finder? Step 1: Calibrate before every scan Place unit flat on wall, press and hold the ON/OFF button at the left side. The red light and green light will flash and the unit will beep. When the green light (Power Indicator) stays illuminated, the calibration is completed. Do not move the unit before calibration Step 2: Scan the wall First slowly slide the stud finder, lock the approximate position of the wood stem (For more accurate test results ) Press the button and slowly move the digital wall scanner along the wall. * If you shake or accidentally lift the scanner, you will need to recalibrate the device Step 3: Find the location of the stud Then beeping sound and 4 signal strength light will let you know there is an edge, mark it ！ Same process from another slide, you will get another edge, you found the stud Detection is achieved using two different methods: 1. Magnetic Uses powerful magnets to pinpoint the location of screws or nails in a stud. Therefore it doesn't detect the stud itself but rather the hardware that attaches the wall material to the stud. 2. Electronic Electronic stud finders rely on sensors that detect changes in the dielectric constant (the relative permittivity) of the wall. This changes when the sensor is over a stud. The lower reading indicates the presence of a stud in the wall and the signal will let you know by the colored lights. eOUTIL ST102 stud finder is an electronic style. *When the product battery is lower than 7.8V, the product may indicate low voltage, the first yellow LED light will flash, and the buzzer will sound, indicating that the product can no longer be tested at this time, and a new 9V battery needs to be replaced

Características

• Precisión de nivel profesional: el escáner de pared puede localizar los bordes de vigas de madera o metal de hasta 3/4 de pulgada (20 mm) de profundidad. Ya sea que esté colgando un marco de fotos o un televisor en la pared, o comenzando una renovación completa de la habitación, un detector de vigas en el que pueda confiar es imprescindible
• Operation is Simple & Easy to Calibrate: Just press the button, it beeps right away for 1~2 seconds, When the green light (Power Indicator) stays illuminated, the calibration is completed. When it's done, now you can slide it around to detect (keep holding button) until you find the edge of a stud
• Light Indicator & Audio Alarm: ST102 stud finder has LED light Indicator and the sound warning to detect the accurate location of the objects. When approached or be located the target, Light Indicator will indicate the direction, and the intensity of beeping tells whether you are more close to the target. The beam finder make your work and life more
• Ergonomic Grip for Comfortable Use: The ergonomic design of this wall stud finder makes it comfortable to hold from any angle. Its small profile is easy enough to store in a drawer or toolbox. Specification: 5.78 x 2.44 x 1.26 inches
• What You Will Get: 1 x Stud Finder, 1 x User Manual; It uses with a 9V 6F22 battery as a power source. When calibrating, please take off the ring to prevent the metal from bringing errors to the calibration

Especificaciones