F722/F411 40A AIO Flight Controller 4 in 1 ESC Combo,BLHeli_S, 2-6S Lipo, Compatible with O4 Air Unit, for Tiny Whoop, Whoop FPV Drones, Quadcopter and RC Builds (F411)

Descripción

Product description Featuer： 1. The PCB adopts high-end 8-layer 2oZ thickened copper sheet, high-end resin plug hole PCB production process, dual pad design, stronger overcurrent capacity, and good heat dissipation. 2. MOS adopts imported 40V high current withstand MOS, with long service life and strong load capacity. 3. Adopting industrial grade LDO, resistant to high temperature. 4. Adopting high-quality Japanese Murata capacitors with strong filtering performance F722 FC Built-in 40A BLHELI_ S 2-6S AIO ESC Flight control parameters: CPU: STM32F722RET6 / IMU: ICM42688 OSD: AT7456E / Barometer: integrated BEC: 5V/3A / Uart: 5 LED: Support WS2812 and other programmable Sensor: Built-in current sensor Flight control firmware version: HAKRC F722D Receiver: CRSF/ Frsky/ Futaba/ Flysky/ TBS Crossfire/ DSMX: DSM2 receiver ESC parameters: Firmware support: BLHELI_ S Protocol support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600 Input voltage: 2S-6S Lipo Continuous current: 40A Peak current: 50A Current meter proportional value: 450 Firmware version: BLHELI _S (G- H-30) Description: Size: 32* 32mm (25.5mm-26.5mm mounting hole) Packing size: ø63*32mm Product net weight: 7g Package weight: 25g Package Included: 1x F722 Flight Controller AIO 4x Yellow shock-absorbing ball 1x XT30 power cord 1x Type-C USB small board 1x 80mm long SH1.0/7P single-head cable 1x 270uf/35V capacitor F411 20A AIO Flight Controller: CPU: STM32F411CEU6 IMU: ICM42688 OSD: AT7456E Barometer: SPL06 LED: Suppotr programmabled such as WS2812 Current meter: Yes Firmware: HAKRC F411D Support receiver: Frsky/ Futabas/ Flysky/ TBS Crossfire/ DSMX:DSM2 ESC: Firmware: BLHELI_ S (G- H-30) Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150，Dshot300，Dshot600 Input: 2S-6S Lipo Con. Current: 40A Peak Current: 45A Specifications： Mounting Hole: 25.5*25.5mm/26.5*26.5mm Weight: 8.5g Package weight: 50g Size: 31*31mm Package Included: 1x F411 40A AIO 4x M2 Shock absorber 1x XT30 power cord 1x Small bandage 1x Type-C USB 1x USB cable 1x 270uf/35V capacitor 1x DJI FPV Cable 1x DJI O3 Air Unit 3-in-1 Cable 1x Instructions Usage Notice (Must Read) Handle with Care During Installation: This flight controller integrates numerous functions with densely packed components. Do not use tools (e.g., needle-nose pliers or socket wrenches) to tighten nuts, as this can easily scratch the hardware and cause unnecessary damage. The correct method is to press the nut firmly with your finger and quickly tighten the screw from the opposite side with a screwdriver. (Caution: Avoid over-tightening, which may damage the PCB board).Safety First - Propellers Off for Setup & Testing: Do not install propellers during installation, configuration, or bench testing. Avoid indoor flight testing to prevent safety incidents. Before installing propellers for flight, double-check that the motor rotation direction and propeller orientation are corre.Use Only Official Standoffs: Do not use non-original aluminum or nylon standoffs, as they may damage the flight controller hardware. The official package includes custom-sized nylon standoffs specifically designed for compatibility with this AIO stack.. Important Safety Warning: Do not fly near crowds. Our company assumes no liability for any losses or damages caused by aircraft crashes.Pre-Power Checklist: Before powering on the aircraft: Verify all connectors between stack modules are correctly installed (headers and cables must be aligned properly). Double-check the soldering polarity (positive and negative terminals) for correctness. Inspect motor screws to ensure they are not contacting or shorting the motor windings.Inspect for Solder Debris: Examine the electronic components on the flight stack for any stray solder splashes or bridges, which could cause short circuits. The buyer assumes all responsibility for any short circuits resulting from installation or soldering. See More

Características

• 【High-End 8-Layer 2oz Copper Design】 Premium PCB with thick copper layers drastically improves current handling and heat dissipation, ensuring rock-solid stability and longevity even under heavy loads.
• 【Industrial-Grade Components】 Built with imported 40V MOSFETs, industrial LDO, and Japanese Murata capacitors for exceptionally clean power delivery, reduced video noise, and maximum reliability.
• 【Powerful FC & 40A ESC Combo】 The STM32F722/F411 processor and ICM42688 gyro deliver precise control. The integrated 40A BLHeli_S ESC supports Dshot600 for ultra-responsive motor control from 2-6S.
• 【O4 Air Unit Compatible & Complete Kit】 Fully compatible with DJI O4 Air Unit for digital HD video. Comes with all necessary parts (XT30 cable, capacitor, USB board) for a quick and easy installation.
• 【Ideal for Tiny Whoop & FPV Drones】 The compact AIO design is the perfect choice for building powerful and durable Tiny Whoop圈圈机, 5-inch quadcopters, and other FPV aircraft.

Especificaciones