Fuente de alimentación CC ajustable de 900 W, 30 V, 30 A, interruptor de laboratorio variable, banco digital, 60 V, 10 A, 15 V, 30 A/60 A (600 W-60 V10 A, negro)

Descripción

The safety symbols below will appear in this manual or on theDC power supply.PRODUCT BRIEFThe R-SPs series of adjustable regulated DC Power Supplydesigned for use in laboratories,schools and production lines.Both output voltage and output current are continuously adjustablebetween 0 and nominal.The stability and ripple factor of the power supply are very goodand have a protection circuit. Can work at full load for along time.This power supply can be used as both a regulatedpower supply and a regulated current supply.<;80%RH, andpreheated for 30 minutes.The actual parameters will varyslightly.WORK REQUIEMENT1.AC input: Please make sure the input voltage of this product230V10%50Hz 115 V10%60Hz2.Do not use in an environment where the ambient temperatureexceeds 40 degrees The cooling fan is located at therear of the device and should have enough space for cooling.1. Turn on the powe switch2. Adjust the voltage adjustment knob to 5V3. Connect the "positive" and "negative" with wires and adjustthe current knob to 5A.4. Disconnect the wire and connect the load to use.Attention:ln actual CV operation, if the load resistance decreases and theoutput current increases to the set current value, the power supplywill automatically switch to cC mode. When the load resistancevalue continues to decrease, the current will remain at the currentset value.The voltage is proportionally reduced.At this time, increase the load resistance or increase the current set value torestore the CV output state.CONNECT THE LOAD1. Rotate the terminal knob by turning it counterclockwise2. Insert the load terminal3. Turn the terminal knob clockwise4. Bananacan be directly inserted into the terminal holeAttention:lmproper connection may result in damage to the powersupply and the load connected to the power supply. Whenconnecting the battery load, do not reverse the polarity ofthe "+" and"-" as this may damage the power supply.CONSTANT VOLTAGE/ CONSTANT CURRENTCHARACTERISTICSThe working characteristics of this series of power supplies areconstant voltage/constant current automatic conversion type,which can automatically change between constant voltage andconstant current states with load changes.The intersectionbetween constant voltage and constant current mode is calledconversion point.For example, if the load causes the power supply to operate in a constant voltage mode, a constant voltageis output.As the load increases, the output voltage will remainconstant and the output current will increase. When the currentvalue reaches the set current limit value, the power supply willautomatically switch to constant current mode.The outputcurrent remains stable and the output voltage decreases proportionally as the load increases further.The conversion ofconstant voltage and constant current is indicated by the LED onthe front panel.CV indicator light is on during constant voltage, cC indicator ison when constant current.FUSE REPLACEMENT:lf the fuse blows, the power supply will stop working.To find andcorrect the cause of the blown fuse, then replace it with a fuse ofthe same specification.HIGH VOLTAGE!DANGER!For effective safety protection, it is only necessary toreplace the fuse of a specific specification.Before replacing the fuse,the power must be turned off and thepower cord must be unplugged from the power outlet.PRODUCT MAINTANCE1. Disconnect the power when the product is not in use.2.Unplug the power supply before cleaning.3. Do not use hydrocarbons, chlorides or similar solvents, oruse abrasive cleaners.PRODUCT WARRANTY1. This product is offered free maintenance service within oneyear from the date of purchase.Except in the following cases:A: Lack of this product warranty cardB: Failures caused by improper use, such as improper handlingand improper repair, modification or adjustment of the device.C: Consumable materials are not covered by the warranty.D: Naturally irresistible disasters such as floods, fires,earthquakes, etc.2. Maintenance costs are charged for repairs that exceed thewarranty period, and the costs incurred for maintenance are theresponsibility of the user.PACKING LIST1. 1x Power Supply2.1x Power Cord3.1x Output Load Cord4.1x User's Manual5. 1x Warranty CardOutput Power : 201 - 300Wis_customized : YesOutput Current : 0-10AModel Number : AN625-R-SPS1005-BlackOutput Frequency : 50/60HZOutput Type : SINGLE

Características

• 1. Single output, high precision, high reliability, low ripple and noise
• 2. 3LED digital display voltage and current values with mA
• 3. With voltage / current coarse adjustment knob, can adjust the voltage / current value accurately
• 4. Constant voltage constant current operation mode, can be automatically converted
• 5. With current limiting protection

Especificaciones