Anemómetro de hilo caliente AM-284 – Medidor de flujo de aire HVAC para pruebas de conductos y ventilación, cálculo de volumen de aire CFM/CMM, medición de temperatura y velocidad del viento, sonda telescópica recta, software USB para PC

Descripción

Product description Hot Wire Anemometer AM-286 FUNCTION AND SPECIFICATION: Product Type: Industrial hot wire anemometer for HVAC airflow diagnostics; Measurement Principle: Thermal (Hot Wire) – Accurate low-velocity air measurement in ducts and vents; Wind Speed Range: 0.0–30.0 m/s (0–108 km/h, 0–67 mph) – Ventilation testing and airflow balancing; Wind Speed Resolution: 0.01 m/s – Precise detection of small airflow variations; Wind Speed Accuracy: ±3% of reading – Reliable HVAC and industrial field diagnostics; Airflow Measurement: CFM / CMM (velocity × area) – Air volume calculation for duct balancing; Airflow Range: 0–999,900 ft³/min (CFM) / 0–999,900 m³/min (CMM) – Large ventilation system evaluation; Temperature Measurement Range: 0–45°C (32–113°F) – Air temperature verification in HVAC systems; Temperature Accuracy: ±1.0°C (±1.8°F) – Stable ambient and duct temperature measurement; Temperature Resolution: 0.1°C – Fine adjustment during commissioning checks; Supported Velocity Units: m/s, km/h, ft/min, knots, mph – Flexible international workflow; Airflow Measurement: CFM / CMM (velocity × area) – Air volume calculation for duct balancing; Probe Type: High-sensitivity hot wire probe – Stable airflow sensing in ventilation ducts; Probe Design: Bendable telescopic stainless-steel probe (up to 2 m) – Access to hard-to-reach areas; Measurement Modes: Max / Min / Avg / Data Hold – Fluctuation tracking and comparison testing; Data Interface: USB PC connectivity – Data export, analysis and reporting for service documentation; Previous page Next page Previous page Next page Previous page Next page What is the difference between AM-284 and AM-286? Both models use hot wire sensing for airflow measurement and support CFM/CMM calculation. The main difference is the probe design: AM-284 uses a straight telescopic probe, while AM-286 uses a flexible telescopic probe. Can this anemometer measure airflow inside HVAC ducts? Yes. The telescopic probe extends up to 42.1 in (1.07 m), allowing airflow measurement deep inside ducts, vents and ceiling diffusers during HVAC diagnostics and balancing. Can it calculate CFM and CMM? Yes. After entering the duct cross-sectional area, the meter displays airflow volume in CFM or CMM based on the measured air velocity. This helps technicians evaluate ventilation performance during HVAC Is this better than a vane anemometer for low airflow? For low air velocity measurement, hot wire sensors are often more sensitive and stable than vane anemometers, making them suitable for HVAC airflow balancing and weak airflow diagnostics. Can I connect it to a computer for data analysis? Yes. The AM-284 supports USB PC connection for real-time monitoring, exporting measurement data and generating airflow reports for HVAC inspections and system performance analysis.

Características

• ANEMÓMETRO DE ALAMBRE CALIENTE AM-284 PARA DIAGNÓSTICOS DE FLUJO DE AIRE HVAC – Diseñado para técnicos que miden el flujo de aire dentro de conductos, respiraderos y sistemas de escape. Ideal para equilibrar los sistemas de ventilación, verificar el rendimiento del flujo de aire y diagnosticar un flujo de aire débil en instalaciones de HVAC.
• AIR VELOCITY AND AIRFLOW MEASUREMENT IN ONE DEVICE – Measure wind speed and calculate airflow volume in CFM or CMM by entering duct area. This helps technicians evaluate ventilation performance during commissioning, maintenance inspections and airflow verification.
• REMOTE TELESCOPIC STRAIGHT HOT WIRE PROBE FOR DUCT ACCESS – The extendable straight probe retracts to approximately 11 in and extends up to 42.1 in (1.07 m) for measurements deep inside air ducts, ceiling diffusers and ventilation outlets. Includes a 39.37 in (1 m) cable for flexible positioning.
• HIGH SENSITIVITY HOT WIRE SENSOR FOR LOW AIR VELOCITY – Thermal hot wire sensing technology provides stable airflow measurement where traditional vane anemometers often lose sensitivity, especially in low-speed ventilation systems.
• MULTIPLE WIND SPEED UNITS FOR DIFFERENT WORKFLOWS – Supports m/s, km/h, ft/min, knots and mph, allowing technicians to work with measurement units commonly used in HVAC diagnostics and industrial airflow testing.
• MAX MIN AVG AND DATA HOLD FUNCTIONS – Capture fluctuating airflow conditions, record maximum or minimum readings and freeze measurements for documentation during duct balancing or ventilation system inspection.
• BACKLIT LCD FOR LOW-LIGHT HVAC ENVIRONMENTS – The illuminated display allows easy reading inside mechanical rooms, ceiling ducts and equipment spaces where lighting conditions are limited.
• USB PC CONNECTIVITY FOR REPORTING AND ANALYSIS – Connect the device to a computer for real-time monitoring and exporting measurement data, supporting airflow documentation and system performance reporting.

Especificaciones